Reasons Your Fiat 500 Key Fob Won't Work
A key fob for Fiat 500 makes it simple to open doors and start your car. There are many reasons why the fob could stop working. This could be due to a dead battery, water damage, receiver modules issues, and interference.
This listing is for a NEW replacement Fiat Flip Key Remote - similar to the Ilco brand that must be professionally programmed by a local locksmith (click here for Locksmith Search). Includes lock, unlock, and trunk buttons.
Dead Coin Battery
A dead battery is the main reason for your 500 key fob being inoperative. Key fobs of today have a limited range of operation and must be within just a few inches of the vehicle to function. If you're far away from your vehicle when you press the key fob button, the car won't respond, and will display the "Key Fob Not Detected" message in the instrument cluster.
If this happens If this happens, replace the battery in the coin-cell (Part Number CR2032) by a fresh one of a trusted brand such as Panasonic Duracell or Energizer. They are usually available in your local hardware store, or online.
You can test the battery of your coin-cell by pressing the buttons while you are standing close to your Fiat 500. The parking lights should flash and the key fob should operate the lock and unlock switch.
If your key fob does not work after replacing the battery, it may be water damage which has prevented it from communicating with the module inside your vehicle. Water damage can occur in a variety of ways, from an accidental splash to submerging the fob in salt water at the beach. If mouse click the following internet site suspect that your fob was exposed to water, try placing it in a dry rice bag to pull the moisture out. If that doesn't work, your fob may need to be reset by an experienced auto locksmith or dealer.
Water Damage
While the fob comes with rubber seals that keep water from the electronic chip inside, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater is particularly dangerous to the circuit board of the fob and can cause it to short out and eventually end up dying. In the event that you let your fob get wet, it's not an ideal choice but if you accidentally drop it in a cup of water or don't remember to take it out of your pants pocket before running the washer, don't give up hope.
Remove the battery first. Before replacing the battery clean the electronic chip using isopropyl, or a similar product. Next try the fob and verify if it is working. If the key isn't working, it may have to be changed. This is typically handled by a dealer or professional auto locksmith.
If the key is more recent and has not been programmed to your car, it will likely need to be replaced completely. A professional automotive locksmith can carry out this simple task. The locksmith will have to cut the key to match the ignition of your vehicle. They'll also have to reprogram the fob for your vehicle's system. This is a quick and cost-effective process that can be completed in the next day.
Receiver Module Issues
One of the simplest reasons why your 500 key fob may stop functioning is that it's out of range. The remote has a range of 30 feet. So should you be too far from your car it won't be able to respond to your commands. This can be easily fixed by moving it closer to your vehicle until it starts responding.
If you've replaced your coin battery (commonly called"button" or "button" or "watch") and your fob still won't work, it could have an internal circuit board problem. Reprogramming the fob usually resolves the issue. You can find instructions on how to do this on the majority of automobiles by searching YouTube or reading the owner's manual.
It is possible to replace the metal clips that hold the battery of your coin in place. If they lose tension it could prevent your coin battery from being properly seated and cause your remote to malfunction.
In rare cases the fob could be out of sync with your vehicle because of hardware or software problems. This can cause a major headache, but you can usually resolve this issue by visiting an auto locksmith to have them reprogram your fob. In some instances, they may need to reinstall the program in your body control module, as well.
Interference
In addition to a dead battery on a coin the key fob could not be able to transmit or receive the signal due to interference. This can occur when the keyfob is in close proximity to a radio transmitter, like a cell phone or radar detector. The key fob might not function because of a problem to the buttons or water damage, or damage to the internal chips.
If your key fob suddenly stopped working, or you've tried everything at home to fix it (e.g. battery replacement, reprogramming and using the spare key fob, you might have a defective receiver module on your 500. The receiver module is situated under the dash, and it picks up the radio frequency signals from the key fob. It transforms the signals into electronic commands that are then interpreted by the vehicle.
There's a simple method to reset the 500's onboard system, including the keyfob. Disconnect the battery 12 volt for approximately 15 minutes by taking off the negative cable first then the positive cable. Reconnect the battery. This will eliminate any remaining electrical charge and restart the car's computers, which can help you the key fob to function again. If the issue continues you should speak with an experienced technician. They'll be able determine the root of your issues.